<var id="7kd72"><sup id="7kd72"></sup></var><thead id="7kd72"><tt id="7kd72"></tt></thead>
<font id="7kd72"><del id="7kd72"><track id="7kd72"></track></del></font>

<object id="7kd72"><rp id="7kd72"><big id="7kd72"></big></rp></object>

    <font id="7kd72"></font>

      <nobr id="7kd72"><tt id="7kd72"><p id="7kd72"></p></tt></nobr>

        <font id="7kd72"></font>

        ?
        输送带导航/TEL:0312-8391666
        输送带行业新闻

        输送带-输 [shū] 送机离合器 [qì] 润滑油黏 [nián] 度

        作者:河北橡胶输送带  来源:   发布时间:2019-02-03 11:20:06

        输送带-输 [shū] 送机离合器 [qì] 润滑油黏 [nián] 度??捎昧街嗤?[xiāng tóng] 的试管(或细瓶),一支装标准 [biāo zhǔn] 黏度油,另一支装被 测 [cè] 油样。使两者油面高度 [gāo dù] 相同,并将管口堵塞后倒置,观察试管内气泡 [qì pào] 上升快慢、气泡上 升快,油的黏度??;反之,油的黏度大。
        输送机离合器油液清洁 [qīng jié] 度。将被测油样放人试管或瓶内,按|个方向旋转 [xuán zhuǎn] 摇动,静置后观察将刮刀 [guā dāo] 均衡地与输送带接触 [jiē chù] ,刮刀位置应在头轮或尾轮的水平中心线下,同时 刀头必须指向头轮、尾轮;刮刀位于输送带下方且垂直 [chuí zhí] 于带面;固定夹紧 [jiā jǐn] 器。刮刀与输送带接触时,调整杆应低于水平线,而后拧紧调整杆的固定螺钉 [luó dīng] 。调 整杆下倾可便于上拧调整螺钉以调整刮刀的压力 [yā lì] 。一般调整螺钉上拧2.5 ~3圈,调整杆 上升5 ~5. 25mm (上顶输送带高度),刀片对输送带的压力约7 ~8kg。
        调整好后,拧紧 [nǐng jǐn] 调整螺钉的锁紧螺母。

        Conveyor Belt - Conveyor Clutch Lubrication Oil Viscosity. Two identical test tubes (or thin bottles) can be used, one for standard viscous oil and the other for tested oil samples. The height of oil surface is the same, and the orifice of the tube is blocked and inverted to observe the rising speed of bubbles, the rising speed of bubbles, and the viscosity of oil is small; on the contrary, the viscosity of oil is large.            Oil cleanliness of conveyor clutch. The measured oil sample is placed in the test tube or bottle, rotated and rocked in            When the scraper contacts the conveyor belt, the adjusting rod should be lower than the horizontal line, and then tighten the fixing screw of the adjusting rod. The downward inclination of the adjusting rod makes it easy to screw up the adjusting screw to adjust the pressure of the scraper. Generally, adjusting screw is twisted 2.5~3 times, adjusting rod rises 5~5.25 mm (top conveyor belt height), blade pressure on conveyor belt is about 7~8 kg.            After adjustment, tighten the locking nut of the adjustment screw.



        相关阅读

        相关产品

        ?