<var id="7kd72"><sup id="7kd72"></sup></var><thead id="7kd72"><tt id="7kd72"></tt></thead>
<font id="7kd72"><del id="7kd72"><track id="7kd72"></track></del></font>

<object id="7kd72"><rp id="7kd72"><big id="7kd72"></big></rp></object>

    <font id="7kd72"></font>

      <nobr id="7kd72"><tt id="7kd72"><p id="7kd72"></p></tt></nobr>

        <font id="7kd72"></font>

        ?
        输送带导航/TEL:0312-8391666
        输送带行业新闻

        输送带 [shū sòng dài] 在运输和贮存中,应保持 [bǎo chí] 清洁

        作者:河北橡胶输送带  来源:   发布时间:2019-02-02 10:42:33

        1、 输送带 [shū sòng dài] 在运输和贮存中,应保持 [bǎo chí] 清洁,避免阳光直射 [zhí shè] ,雨雪浸淋,防止与酸 、 碱、油类,有机溶剂等影 响橡胶 [xiàng jiāo] 质量的物质接触,并距离发热装置1米以外。
        2、 贮存时库房 [kù fáng]内温度宜保持在—15℃—+40℃之间,相对湿度宜保持 [bǎo chí] 在50—80%之间。
        3、 贮存中输送带须成卷 [chéng juǎn] 放置,不得折叠,放置期间应每季翻动 [fān dòng] 一次。
        4、 输送带运行速度 [sù dù] 不应大于5.0米/秒,运输块度大,磨损 [mó sǔn] 性大的物料和使用固定犁型卸料装置时应尽量采用低速。超出规定速度时,会影响胶带 [jiāo dài] 使用寿命。
        5、 运输机 [yùn shū jī] 的传动滚筒直径与输送带布层的关系,传动滚筒改向滚筒 [gǔn tǒng] 的配套以及对托辊槽角的要求,应根据输送机的设计规定,合理 [hé lǐ] 选取。
        6、 为减轻物料 [wù liào] 对胶带的冲击与磨损 [mó sǔn],给料方向应顺胶带的运行方向;物料下落到胶带 [jiāo dài] 上的落差应尽量减??;给料口应避开 [bì kāi] 滚筒或托辊的正上方;胶 带受料段应缩短 [suō duǎn] 托辊间距 和采取缓冲 [huǎn chōng] 措施。为防止刮破胶带 [jiāo dài] ,挡料装置刮板清扫 [qīng sǎo] 装置和卸料装置与胶带的接触部分 [bù fen] 应采用硬度适宜的橡胶板,不要采用夹有布层的胶带 [jiāo dài] 头。
        1. In transportation and storage, the conveyor belt should be kept clean, avoid direct sunlight, rain and snow leaching, prevent contact with acid, alkali, oil, organic solvents and other substances affecting the quality of rubber, and away from the heating device 1 meter. 

        2. During storage, the temperature in the warehouse should be kept between - 15 and + 40 and the relative humidity should be kept between 50 80%. 

        3. Conveyor belts in storage should be placed in rolls and not folded. They should be turned up once a quarter during storage.  

        4. Conveyor belt speed should not be greater than 5.0 m/s. Low speed should be used when conveying materials with large fragmentation and abrasion and using fixed plough unloading device. When the speed exceeds the prescribed speed, the service life of the belt will be affected.       

        5. The relationship between the diameter of the driving drum and the distribution of the conveyor belt, the matching of the changing direction of the driving drum and the requirement of the groove angle of the idler should be reasonably selected according to the design regulations of the conveyor.    

        6. In order to alleviate the impact and wear of the material on the belt, the feeding direction should follow the running direction of the belt; the drop of the material falling on the belt should be minimized; the feeding outlet should avoid the top of the drum or idler; the feeding section of the belt should shorten the distance between idlers and take buffer measures. In order to prevent the scraping of rubber tape, the scraper cleaning device and the unloading device of the baffle device should adopt rubber plate with suitable hardness, and the tape head with cloth layer should not be used.

        相关阅读

        相关产品

        ?